HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Vuktilar Masar
Country: Gabon
Language: English (Spanish)
Genre: Music
Published (Last): 2 April 2005
Pages: 271
PDF File Size: 6.25 Mb
ePub File Size: 20.28 Mb
ISBN: 886-6-28259-129-2
Downloads: 97636
Price: Free* [*Free Regsitration Required]
Uploader: Tojinn

In the above circuit I have set the 8-bit address data as 0b, by connecting ci address pins to ground. Interface GPS with Arduino.

This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. What is Web Browser. HT12E is an encoder integrated circuit of 2 12 series of encoders. Submitted by admin on 30 October We should set the bits in same pattern on Encoder and Decoder IC to pair them.

The IC has a built in oscillator.

As soon as TE returns to high, the encoder output completes its final cycle and then stops. They can also be connected to switches to manually send and receive data. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable.

SPI Module of Arduino. Pull the Transmission Enable pin pin 14 to ground to activate transmission. Simply put, HT12E converts the parallel inputs into serial output. Choosing Battery for Robots. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the dtasheet side of the HT12D decoder IC.


It is mainly used in interfacing RF and infrared circuits.

This oscillator can be used by connecting these two pins through a 1M Resistor. These 12 bits are divided into 8 address bits and 4 data bits.

Supply voltage; 5V 2. If you want security you can connect any of the 8 pins to 5V to make it high. These two ICs together form an Encoder and Decoder pair. Skip to main content.

For decoding a data iic IC will requires an oscillator, luckily this IC has one in-built.

HT12E Datasheet

Virgin Galactic — Commercial Space Flight. The IC is has h1t2e wide range of operating voltage from 2. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the eatasheet A0 to A7. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. HT12E has a transmission enable pin which is active low. Choosing Motor For Robots. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. TL — Programmable Reference Voltage. Connected to the Ground of circuit. This pin has datawheet be connected to Ground 0V to enable the Transmission. This high-density System-in-Package SiP integrates controller, power switches, and support components. The encoded bit can be obtained from the Daasheet pin pin Can range from 2.


HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

It is very important that your Decoder should also have this same address for them to talk to each other. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Ut12e or Fire alarm system etc.

You can know to set up the HT12D after this from here. The Encoded 12 bit output data can be obtained from this pin. They are paired with 2 12 series of decoders for use in remote control system applications. These are the 8-bit address bits, which is used to protect your data. So if you are working on datasjeet project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

Arduino based GPS receiver. Transmission enable; active low.

HT12E Encoder IC

Interface SD Card with Arduino. This cycle is repeated as iv as TE is kept low. The primary function of HT12E is to encode a bit and send it out through the output pin.